See what our Experts say about this Dexter Trailer Brakes

• Do I Have To Adjust New Dexter ABS Brakes After Installing On Trailer?
  Nope - that’s one of the perks of these. All models of Dexter ABS Brake Assemblies, such as 3.5k # DX73WR, 4.4k # DX83WR, 7.5k # DX23WR, and 8k # DX55WR, are Nev-R-Adjust brakes. They’ll automatically maintain the proper shoe clearance once they’re burnished in. Just make sure to follow Dexter’s break-in procedure - about 20–30 controlled stops from 40 mph - so the shoes seat evenly. Brian, are you replacing a single axle or doing all four corners? It’s best to do them all at the same...
  view full answer...
• What Is The Difference Between Dexter ABS 4400lbs And 3500lbs Brake Assemblies? Both Are 10"
  Good catch, Allen - both the 3.5K # DX73WR and 4.4K # DX83WR use 10 inch x 2-1/4 inch shoes, but the 4.4K version is built for a heavier spindle and a different bearing combo. The 4.4K uses L68149 inner and LM67048 outer bearings, while the 3.5K uses L68149 and L44649. The backing plates are different bolt patterns and the sensors are tuned for those axle specs, so they’re not interchangeable. If you’re unsure which axle you’ve got, measuring your tube diameter (2-3/8 inch for 3,500lbs...
  view full answer...
• Are Dexter And Lippert ABS Brakes Interchangeable On 4,400lb Axles?
  Steve, they’re not - the Dexter ABS Brake Assemblies # DX83WR are designed for Dexter’s ABS Tow Assist 4.4K axles and won’t clear the flange profile used on Lippert axles. The offset and magnet alignment differ just enough to cause interference. Also, the main thing is that the ABS connections are different and won't be cross-compatible with the ABS systems. If you’ve got a Lippert axle, you’ll need to stick with Lippert-specific ABS brake assembly. Do you happen to know your axle tag...
  view full answer...
• Are Dexter ABS Brakes For 3,500lb Axles The Same Fitment As 4,00lbs Axles?
  Good eye, Brian - both the 3.5K # DX73WR and 4.4K # DX83WR Tow Assist brakes are 10 inch x 2-1/4 inch, but they’re not interchangeable. The 3.5K version uses different mounting offsets and lighter components for smaller spindles, while the 4.4K version fits a heavier hub and uses a slightly different bearings. If one axle tag shows 3,500 and the other 4,400, replace each axle with the matching rated assembly so the ABS sensors read correctly. Are you planning to replace all four at once,...
  view full answer...
• Dexter ABS Module Amber Light On After Installing New ABS Brakes DX83WR 4400lb Axle
  Carlos, that amber light means the Tow Assist system isn’t detecting one of the wheel sensors. Start by double-checking that the ABS connector from the 10" 4,400lb ABS Brake Assembly # DX83WR you replaced is fully seated and that no pins are bent. Also inspect the harness for pinched wires near the flange. Once you confirm both sides are connected cleanly, cycle power to the system - it should switch back to green if everything’s good. Did it go amber immediately after startup, or only...
  view full answer...
• Amber Light On Dexter Tow Assist Monitor After Installing New ABS Brakes 4,400lb Axle
  Greg, that amber light means the Tow Assist system isn’t reading one of the wheel sensors. Start by checking that both brake and ABS plugs are fully seated on your # DX83WR assemblies. Also look for bent pins or dirt in the connectors. Once they’re clean and reseated, cycle the trailer power - it should switch back to green. Rarely do we see a defective sensor, but if that happens to be the case, you'll reach out to Dexter for that. Did this happen immediately after the install, or only...
  view full answer...
• 10" 4,400lb Replacement Brake Assemblies For Dexter Tow Assist On Small Travel Trailer
  Yes, Rob, for 4.4K Tow Assist axles you’ll want the 10 inch Dexter ABS brakes # DX83WR. They use the same 4-bolt flange as your original setup and connect directly to the existing harnesses/plugs. Just torque the nuts to 45–50 ft-lbs and spin the hub to make sure the sensor isn’t contacting the tone ring before lowering the trailer since you don't want to damage that. If the sensor gets damaged, you'll have to get one from Dexter. Will you be swapping both axles, or just one for now? Anyone...
  view full answer...
• Do 4.4k ABS Brakes From Dexter Need Adjustment Or Are They Like Nev-R-Adjust ?
  Yes, Kendra. The Dexter 4.4K ABS assemblies # DX83WR include the same Nev-R-Adjust system as Dexter’s standard brakes. Once you’ve done the break-in procedure 20–30 slow stops, they’ll maintain shoe clearance automatically. Are you upgrading both axles at once? It’s always smart to match new brakes side-to-side so the ABS can balance correctly. Anyone else running the Tow Assist setup - how’s your braking feel so far?
  view full answer...
• Does etrailer Have Complete Dexter ABS Kit
  Hi Zackory, we have replacement parts for the Dexter ABS system but we don't have a complete kit. Because of the installation, and the need for calibration with some special parts/equipment, you will need to have this completed at an authorized dealer.
  view full answer...
• Do 10" Dexter ABS Brakes Need Adjusted After Installation Like Old Trailer Brakes Do?
  No manual adjustment needed, Chad - both the 3.5K # DX73WR and 4.4K # DX83WR assemblies feature Dexter’s Nev-R-Adjust design. Once installed and burnished in, the internal tensioning cable automatically maintains the proper shoe clearance. You’ll still want to follow Dexter’s initial break-in procedure 20–30 gradual stops so the shoes seat evenly with your drums. Do you know which brake assemblies you need? If not, let me know and I can walk you through it!
  view full answer...

Do you have a question about this Trailer Brake?